Videos & Guides
Expand a section to see a video and/or written guide.
Sizing out T-Tape
We’ll have to get our measurements that’ll be used every time we make a T-Tape.
Grab a measuring tape and begin by getting the circumference of your fully erect penis, around the circumcision scar.
*T-Tape is applied to a fully erect penis. This helps so the penis isn’t restricted by the tape when erect or during nocturnal erections if using while asleep.
(picture of tape measure around penis)
Make sure to get a little overlap around, about .25 inches. Convert the measurement to cm and write this down.
This will be the size we cut out for each t-tape from the roll.
Unroll some tape. Each square is one cm.
(picture of tape being unrolled)
Going lengthwise, cut out a piece of tape from the measurement we made earlier.
(Picture of cutout tape)
We can now begin to create a t-tape.
Folding T-Tape
(video of folding t-tape)
The tape has 3 parts on the peel side: two 1.25cm small peel tabs and one big middle peel tab.
(picture of piece of tape)
First we’ll move the big middle peel, careful to not make any creases.
(Picture of tape with no middle peel)
And then we’ll take the bottom tab and bring it up to the top tab by folding along the middle of the tape. We want to try and perfectly align the tabs together.
(Picture of tabs meeting)
Once together we’ll taper the bottom area down to adhere the area without a peel. Don’t worry if there’s some creases as this part of the t-tape serves as an area to grab onto with a tugger or our T-Tape Topper.
(Close of tape before tapering)
(Picture of Folded tape)
Finally fold the tabs down, one for each respective side as we now have our T-Tape.
(Picture of T-tape assembled)
With enough practice you’ll easily make these in a minute or less!
(gif of folding tape)
Applying T-Tape
(Video of applying T-Tape)
Before applying T-Tape, make sure your penis is fully erect.
*T-Tape is applied to a fully erect penis. This helps so the penis isn’t restricted by the tape when erect or during nocturnal erections if using while asleep.
Remove the peel from the two tabs of the T-Tape. Careful to make sure the tabs don’t adhere to eachother.
(picture of t-tape with tab peels off)
The middle between the two tabs is where it will adhere to the circumcision scar. Hold the tape like the picture below. The top tab will be on the inner skin of the penis, while the bottom tab will be placed on the outside skin.
(picture of tape held before placing)
Carefully the side of both tabs on to the erect penis, aligning the middle of the tape to your circumcision scar. Roll the tape around the penis, tracing the scar. Make sure the tabs don’t stick to each other while doing so.
(picture of tape going around circ scar)
Finally once a loop is done, you should have some left if you followed the sizing out guide. We will overlap the starting point a bit.
(Pic of tape applied and overlapping)
Now it is recommended to massage the adhered part of the tape while erect for about 3-10 minutes. We want to make sure the tape is fully adhered to the skin and won’t prematurely come off.
Congrats! Your t-tape is now applied. Now we’ll add some tension to start stretching. This can be done with a bedsheet suspender, or our T-Tape Topper & Tugger Strap combo shown below.
FasT-Tape
T-Tape Topper Sizing
With your penis fully erect, roll a sheet a paper around your member.
(picture of paper around pen)
Take a measuring tape and measure the diameter of the paper opening. Convert the measurement to mm. Pick the size closest to our topper options [] give or take some mm’s. Fabric will attach to the top of the T-Tape fabric once secured with a rubber band.
(pic of measurement tape to paper)
Assembling Topper
(picture of unassembled topper parts)
The topper comes in five parts:
- The lid
- The base
- 1 big rubberband
- 2 small rubberbands
Take the lid and apply one small rubberband to one side of the open slit, and stretch it to the one across. Do the same for the next small rubberband.
(pic of one rubberband on)
(pic of lid with both rubbers)
Take the lid and screw it onto the base.
(pic of screwed topper)
The Topper is now ready to be applied to the T-Tape.
Applying Topper and Tugger to T-Tape
(Video of applying topper and tugger)
Put the topper into the opening of the t-tape, base side in. The base of the topper has a groove. Align the groove a bit under the top of the t-tape.
(pic of topper in tape)
Take the big rubberband and put it around the outside of the tape into the groove of the topper base. Fold the rubberband and apply twice if needed.
(pic of applied topper)
Now we can add some tension. With the Tugger Strap clip the claw onto the middle intersection of the lid rubberbands.
(pic of claw on rubberbands)
With the Tugger Strap, there are a plethora of ways and positions to add tension. We can clip the end to a knee brace, over our shoulder or down our leg. My recommendation is with the penis sticking out of a comfortable pair of boxers, take the end of the tugger and clip it around the waistband of the boxers.
(pic of tugger on boxers)
With pants on this makes a perfect discreet way of tugging. I’m able to even sleep comfortably with this method.
To adjust tension, either adjust where the clip is placed or adjust and move the buckle to loosen the tugger.
(pic of buckle on tugger)
Remember that you should only use as much tension to the point where you can barely feel it and there’s no pain or discomfort.
Happy tugging!